Looking for:
Download EPLAN Electric P8 Reference Handbook Free PDF - . |
Eplan electric p8 pdf free -
You also have to define a source language here. This helps to prevent operating errors, e. Any storage location can be selected using the button. The usual range of templates and basic projects are available for selection. NOTE: These fields cannot be changed later on. It is therefore very impor- tant to make sure you enter the correct data. After defining the above entries, you need to select a template.
This can be a project tem- plate or a basic project. You simply click the More button. You can select the relevant project type in the File type field. EPLAN then returns to the Create project dialog and imports the selected basic project or the template project into the Template field.
The new project is created from the selected basic project. This may take a while depend- ing on the hardware and the storage location server, local. You do not necessarily need to edit these at the moment. This can be done later during project editing. The project proper- ties can now be adjusted or completely changed on the Properties, Structure etc. There is one limitation: The structure of the pages, located in the Structure tab, can no longer be changed grayed out.
It is fixed because the page structure was defined in the basic project. The project can now be edited. This makes it possible, like with terminals, to use the same designation several times PE rail , and the check run will not find any duplicate connection point designations.
Click the Part number field and then use the button that appears to switch to parts man- agement. In parts management, you Fig. Parts management automatically closes after the part is applied.
In contrast to simple part selection, this will offer only devices for selection that fit the exist- ing functions of the symbol in the project. EPLAN data fields and external data fields are assigned in this scheme. Here, the type of data source, the data source itself and, of course, the import scheme field assignment are configured. It is also possible to select a different function definition instead of the default terminal.
Generate functions Just click the button. However, this is not a precondition. All function definitions can be easily changed later using block editing in the terminal strip navigator. We return once more to generation of the functions: The functions can only be generated when all entered data is correct EPLAN will enable the OK button. If an error exists in the numbering pattern, e. You must check for this. This data must can be assigned later using device selection.
The entries are similar to the previous section. You need to select a DT, a numbering pattern, and, most importantly, a part the device from parts management.
When all entries are correct, you can start device generation by clicking the OK button. EPLAN saves the functions in the navigator as unplaced functions. They already have parts data. What is a main terminal? It is comparable to a main function; a terminal with multiple function definitions can only be identified once as a main terminal.
These are so-called auxiliary terminals. The functions in the logical PLC overview and the functions in the schematic for the PLC terminals in distributed view will be re- addressed or addressed for the first time.
In the PLC navigator, you select the card to be addressed. EPLAN obtains the relevant prefix, meaning whether an entry begins with E or with I, according to the selected scheme, which is entered in the PLC-specific settings selection field. I recommend leaving the Preview of result parameter switched on. Address PLC connection points Fig. The NEW. Here you must make the desired entries and save the properties. You can also immediately perform a device selection for the new PLC card.
All objects are assigned to this macro box now. EPLAN selects the corresponding objects. The Reports tab is usually empty before reports are generated from the project data for the first time, i. Left area with tabs Fig. Auflage Taschenbuch. However, this is not compulsory! This means that EPLAN allows the user to decide whether a project is error free or not and which priority a message error, warning, or note should have. Of course, it is possible to avoid even such errors.
With the Prevent errors check option, the above approach would not be possible. But this is a freely adjustable setting. This will be clarified with a small example. If I select three texts on a page and start the translation function, then exactly these three texts will be translated.
If I select this page in the page navigator, then the translation function will translate all texts on the entire page, depending on their settings.
EPLAN is an online system. All references or device data are kept constantly i. The only limitations if you want to call them this relate to connection data. For performance reasons, these are only updated as desired via a few specific actions, the rest is performed completely independently by EPLAN. A typical example of this is the editing of a page followed by a page change.
If required, here you need to manually start the updating of the connections. However, this can negatively affect the performance of a project. In my opinion, constant online updating of connections is not really necessary because relevant actions such as graphical project reports or automated procedures such as device numbering automatically update the connections before the actual action is performed.
This means that the devices symbols can first be placed in the schematic and the devices symbols can then be subsequently assigned the parts, including the associated function definitions.
This is not compulsory, and you have a completely free choice when editing a project. After calling up for the first time, this can then always occur automatically. Here too, you must carefully consider whether automation at this point is actually useful. EPLAN lets the user decide. This logical information must be specified for the symbols, forms, or plot frames so that it is visible. This is done by assigning properties. Every property has a property name and a property number that is only valid for this single property.
You can use the property number to gain an approximate idea of the area that the property belongs to project, page, etc. The property value assigned to each property is unique to the property. Fig Page properties. The wizard opens the Create project dialog. The dialog contains several tabs Project, PPE, Structure, Numbering, and Properties , and you must enter data into at least the Project tab the PPE tab is only visible when you have a license for this.
Fig Edit the properties of multiple pages All properties that are the same in the selected pages are displayed in plain text. An example would be the scale or grid of the pages. When all entries are complete, the Page properties dialog can be exited by clicking the OK button. EPLAN saves all entries and then closes the dialog Edit page properties directly Apart from the method described for adjusting or modifying Page properties such as page description, etc.
The auxiliary contacts physically belong to the motor overload switch or pushbutton switch symbol and, for the sake of clarity, should also be displayed at the switch. A motor overload switch is inserted into the schematic. The motor overload switch initially has no auxiliary contact at the symbol. As such, this is not a problem, because EPLAN creates a report on the auxiliary contacts used in the schematic on the basis of the settings of the Display tab in the Contact image selection field the selection here is set to On component.
This way, the contacts used and their cross-references are displayed automatically. Fig Automatic cross-referencing This does not matter provided that both or all auxiliary contacts that have such a motor overload switch are also used in the schematic. Not all auxiliary contacts are always used, and EPLAN would display the motor overload switch only with the auxiliary contacts used as graphical representation at the motor overload switch.
The other auxiliary contacts physically exist but are suppressed with this setting. To display those contacts anyway, a device with the appropriate Function definition must be assigned to the Motor overload switch symbol. Fig New device selection.
The Interconnect devices dialog can be filled with various data after it is called up. If these entries are not required, then you can simply delete them. You delete entries by selecting them and then clicking the delete button. If this is not possible, then you can also delete the entries in the fields device source, device target, and cable DT. To do this, you click the field, select the desired entry, and then press the Del key. All entries are deleted after this, and new devices can be selected and interconnected.
New devices are selected in the device source and device target fields using the button. In this dialog, the desired devices for the source and target one of each are selected, and the selection is applied by clicking the OK button.
Fig Interconnect devices dialog. EPLAN finishes the numbering process by writing back the new cable device tags. Fig Changed cable device tags The default settings for the schemes for the different cable editing functions, such as e. Fig Default settings for cable editing functions. All connection point designations are correctly transferred to the PLC terminals.
But this only works if the addresses have been entered correctly. EPLAN derives the data types from the functions. Fig Set data type. Once again, predefined or user-defined filters can be used to control the output of the cable connection diagram and thus display only the required project cables. This is a special form that can be used to e.
Everything is displayed together on a single report page. You can also use the familiar filter and sorting options to e. You use the structure identifier overview to obtain an overview of all the structure identifiers assigned or also unused in the project.
Filters and sorting cannot be selected for devices because these are already manually selected. Filters and sorting can be used for the functions themselves, though data such as plug pin or terminal. The reports hang on the cursor and can now be placed on the active schematic page. Fig All reports are manually placed. Note: The Manual selection option cannot be used with all report types.
This is not allowed for technical programming reasons. Therefore, you should hide the dialog unless you need it. When project editing is almost finished and the project is to be checked for faulty entries, the dialog can be displayed for extra information, since all Errors, Warnings, and Notes generated by the corresponding Check run are listed here.
Fig Message management When you start editing a project in EPLAN, various actions, such as inserting entire pages from other projects or inserting existing macros into the project, can result in unwanted data in the various databases.
For example, unwanted device combinations are created or new structure identifiers are added to the project. You cannot really avoid the creation of such data that do not really belong to the project without being constantly interrupted in your actual project editing.
To make sure that you do not forget to change this unwanted data, EPLAN provides an online monitoring feature, or you can use manual check runs to check the project using a specified scheme offline and generate messages in the message database The visual appearance of message management The dialog supports the user with the following features: Display of the message type, the message priority, and further information such as a brief message description or the jump point to the faulty position in the project.
Small colored icons make it easy to visually distinguish between the different types of messages. Error Warning Note For example: Duplicate connection point designation For example: Connection point description missing For example: A placement lies outside the range. Layers are an essential element originating from mechanical engineering CAD.
Information of the same type e. For example, the form, color, font size or other formats of this layer can later be changed at a central place easily and without errors. This is a great advantage, because otherwise every property that is not located in a layer must be manually edited. The layer management makes such editing actions a piece of cake.
The Layer management dialog is displayed. The layer management is a project-specific setting, and you can recognize this from the window title bar that displays the currently active project. The layer management has the following structure. The dialog has windows at the left and right sides. The left window contains a tree with the superior layer designations nodes and any subnodes and then the layer designation EPLANxyz , and the right window contains the associated sub-entries the actual layer information.
For example, these entries can be used for filtering purposes or as a sorting characteristic for the tree configuration. The entries themselves are limited to characters. Fig Attributes tab The Mounting data tab contains all the information that is necessary to use the part, for example, for a mounting panel layout.
A stored image file can also be useful, because this information is evaluated at different locations in EPLAN. Fig Mounting data tab. To do this, you click the [ Then, the Settings: Compression dialog opens. Fig Settings options for a compression scheme Here you can use the familiar graphical buttons to create a new scheme or copy and change an existing scheme.
In the lower Data to be compressed field, EPLAN offers a number of actions that can be performed during the compression. This setting removes all unused forms from the project and the project then contains only forms that are actually used.
Fig Setting to remove unnecessary forms Note: If, for example, forms documentation was created before the compression, all forms including the unused ones remain stored in the project, because they are needed for the forms documentation. Here, the reports should be removed, especially the forms documentation, prior to the compression.
The other, second, method is to use filters for the compression process. As usual, filters can be set and are either created or edited as schemes. But which project that is does not matter in this context. Fig Example representation for master data opened for editing Generally, you always edit system master data. Fig Prompt when stored master data have been modified If modified master data is also to be used in the current project, following the modification of master data the system master data must be synchronized with the project master data, i.
Otherwise, the modifications to the master data will not take effect in the current project, because they will not have been updated yet at that time. The option to create outlines is not discussed further at this point, because this is a subject related to mechanics and of less use to the actual electrical enclosure project planning.
You can now confirm this selection by clicking OK. Fig Preselection left and selection right of the property EPLAN closes the dialog and transfers the selected placeholder text into the dialog of the same name. Fig Applied placeholder text Now confirm the Placeholder text dialog by clicking OK; the placeholder text now hangs on the cursor and can be placed at any sensible position in the form. Fig Choice of placement As with any other free text, placeholder text can be freely formatted.
This allows the form to be appropriately constructed. It is also possible to subsequently modify placeholder text and select a different one. To do this, select the placeholder text and display its properties by double-clicking or via the popup menu. You then proceed as described above. You use the button to call up the subsequent dialogs and select, apply and place other properties in the usual manner. Upon completion, the form can be checked. To do this, one or more devices are selected and the Place menu entry in the popup menu is selected.
The selected devices are now hanging on the cursor and can be placed in the layout space. Note: The 3D mounting layout navigator only displays those devices that have a part entry. Regardless of whether this part has additional technical data, such as width, height, macro data, or the like! Fig Project-specific setting 1. To do this, you directly activate the mounting panel in the layout space navigator so that the front view is visible in the 3D view.
To do this, you select mounting panel front in the layout space navigator and select the Activate directly entry in the popup menu. Fig Inserted terminal box Fig Selecting the mounting panel front. Before placement, you call up the Placement options.
The upper cable duct should be placed 50 millimeters from the upper edge and 10 millimeters from the left edge of the mounting panel.
Then you should extend the cable duct s length to the right edge, where it is also placed 10 millimeters from the edge. Fig The mounting panel front is now activated. To do this, you directly activate the door s exterior in the layout space navigator and set the view to 3D viewpoint front. You select the signal lamp in the 3D mounting layout navigator, call up the Place function, and then right-click the placement options.
You enter a distance of millimeters from the upper edge of the door. Then confirm the dialog with OK; now you can grab the middle of the upper edge with the snap functions and click the left mouse button. EPLAN now places the signal lamp in the center at a distance of millimeters from the edge. Fig Before placement of the signal lamp This is how the result looks in the 3D view. Fig Grabbing the center Fig Final result: equipped enclosure.
As the name describes, project options are various options for partial areas of a project. This can mean that e. This cannot be implemented using value set macros but is possible using the Project options module. To do this, the desired options are displayed or hidden. Project options cannot be created across projects. They are only available for the project where they have been created. However, template projects with project options can be created Terminology in the Project options module The term project options is always used here.
Project options are a type of generic term. To help to understand project options, the following section contains a brief explanation of the terms used.
Project options group this function allows the grouping of project options. They can contain several project options but only one project option at a time can be switched on. All other project options in the project options group are then switched off. Project options groups can only be created in the project options navigator.
Project options these are partial areas of a project that can be switched on and off as desired. They can consist of one or more extracts, pages, or page areas, or of unplaced objects.
Project options can also only be created in the navigator. Section a section is always assigned to a project option. A section can consist of a partial circuit, a complete page, or several pages. Unplaced objects are also possible in sections. Fig Starting up the project options navigator and the navigator itself. EPLAN offers an easy option for automatically creating reports in a broad range of forms. All that is required is a form of the project options overview type and a report or report template.
The image offers an example of how this kind of overview of the options used may appear in a report. Of course, you can work here with filters and sortings so that for example your report only includes the active options in the form. Fig Generated automatic options overview. Answer: If you see a red exclamation mark on a device, it means that a message has been received for this device via the message navigator.
Fig Symbol properties Simply open the message navigator, check off Selection, select the device in the device navigator, and precisely the message or messages will be displayed that have been generated for this device during the check run.
Answer: In this case, the project in question is not of the schematic project type, but a project of the macro project type. These limitations are typical of macro projects.
No comments:
Post a Comment